TORQUE Airbag Air Bag Suspension Kit for 2015-2025 Ford F150 2WD 4WD F-150 Rear Helper Bag Spring Towing 5000 lbs (Replaces Firestone Ride Rite 2582) (TR2582)

Ok, so this setup got installed on my 2018 F150 STX. I have a motorcycle I carry on the hitch and it squats the truck badly.The torque brand is basically the same as the Airspring, but they didn't spend a bazillion on advertising. The kit is well built, powder coat on parts is nice and not in the threads (common with cheap stuff) and the hardware was nicely bagged/packaged.Now, for the install. I had this thing done, soup to nuts in my garage in under 3 hours. It is a piece of cake if you know which end of a wrench to hold and can follow basic directions. Do the drivers side first, take the wheel off and follow the instructions. Went in easy peasy, an impact wrench speeds things up. Air lines are stupid simple to connect and they did not leak. I use a portable inflator on them, takes about 30 seconds to pump to 70psi for the test.instructions were clearly written by a native english speaker, and have illustrations that helped a LOT.Corrected the sag in the back under load, and for the price, I am extremely happy with this setup. In the event that an airbag pops or leaks, it will be pretty fast to change it out, 3 bolts and a fitting and done. If I bend the steel brackets I've probably got bigger problems, they are built like a tank.

this product was installed and works perfect the only advice would be to make sure cuts made to the end of air line be square and true and inserted full into the housing no issues 3 years and still holding air

I purchased this air bag kit for my 2019 F150. It has a 6 inch lift and 35x12.50r20 tires. Installation was a breeze, except for:1. The flange bolts DO NOT fit the u-bolts. I suspect the flange bolts, as well as the supposed 3/8×1 bolts are actually metric, not SAE, while the u-bolts are SAE. I purchased 3/8×16 nuts for the u-bolts and they fit perfectly.2. The red sealant on the air fittings does not seal the fitting. They leak. As others have mentioned, use teflon tape.

Great airbags system, DO NOT use the flange nuts included for the bail clamps or you will snap them off, go buy a box of Nylon lock nuts 3/8-16 from home depot and 8 washers, this will save you a headache, the airbags hold air, the included tubing is only 15ft long, I bought a longer tubing (50 ft) so I could move the fittings inside gas lid, also purchase a tubbing cutter it will make cutting the tubing straight so much easier so you don't have any leaks, you can buy one for like $7. 2021 F150 with 6" lift, I added airbag cradles so the airbags don't get damage when I go off-roading.

the instructions are crap and the U-bolts suck. kit has nice bags and the bracketry is just fine. None of the parts have labels for where they go. you kind of have to just test fit a ton.the bail clamps are a known failure item. they are supposedly sending me new ones so I will have to see. They sent me new ones. They are the same material. They will give me a credit to buy my own nuts. This is because their metal locks will destroy their bail clamps. Avoid at all cost.

I would buy this kit again. That said, the nuts that come supplied with the U bolts are GARBAGE. Go buy some nice nuts at hardware store before you begin the install. The cheap nuts supplied will stall out and break your U bolt, dont use the supplied nuts. The air nozzle that gets threaded into the bag has pre-applied red "thread sealant"...DO NOT trust this sealant, mine wouldn't hold air. Tape and dope your threads or it will not reliably hold air. They would be better off just supplying you with some tape for the threads. If I would have known those 2 issues prior, install would have been super easy. Still worth the buy, just do those 2 items ahead of time.

Easy to install with even a small mechanical ability, straight forward instructions. Works well so far. Well put together set.

Easy to in stall, had to do a little modification to the lift blocks in the rear under the springs, had to cut a little bit off the sides of the blocks to get the u clamps to clear them which had nothing to do with the air bags, othe than that everything worked great and fit perfectly.