Soft Plastic Ethernet RJ45 Cable Connector Boots Cover Strain Relief Boots CAT5 CAT5E CAT6 CAT6E 100PCS by Copapa (Black)

These push through connectors make putting together ethernet cables a breeze. Thank You.

I use these boots on my 23AWG Cat6 riser cable from TrueCable and (solid bare copper, model 6ECMRWHT_1Kbx) and they fit just fine.

These fit nice and tight around the Cat6 I'm using, and the cover over the retaining clip isn't hard to press when I want to unplug a cable. No complaints.

This is a review of four related products purchased here on Amazon.1. Klein Tools VDV826-703 Pass-Thru™ Modular Data Plug, CAT6, 50-Pack (ASIN B076PRM7W8)2. Klein Tools VDV226-005 Compact Pass-Thru™ Modular Crimper (ASIN B07R3GK9FQ)3. Soft Plastic Ethernet RJ45 Cable Connector Boots by Copapa (ASIN B07219KGC4)4. H!Fiber 1Gbe Ethernet Network Adapter (ASIN B074PPRQQK)I’m using CAT 6 UTP (23 AWG) that I bought from a local home center.1. I found the Klein Tools VDV826-703 Pass-Thru™ Modular Data Plug, (CAT6, 50-Pack) to be easy to use. This is my first-time using pass-thru connectors, and I have mixed feelings, but that’s not what this is about. The 23 AWG wires fit in snuggly but did require a bit of convincing to pass thru. They are more expensive than some others that are available, but I know these will work perfectly, especially with a same brand crimper.2. The Klein Tools VDV226-005 Compact Pass-Thru™ Modular Crimper did its job flawlessly. The insulation is held tightly in place, the crimp felt secure, and the pass-thru wires were cut perfectly flush. I still need to try this with cheap plugs, to see if they are cut just as flush, but these work great with their own.3. While I don’t usually use boots, I decided to give them a shot as they make the wires look more “finished”. I purchased the blue Soft Plastic Ethernet RJ45 Cable Connector Boots by Copapa. While they didn’t cost much, they were very soft and fit okay. I wish they were a little tighter around the wire, but that can vary from brand to brand. Overall, I’m happy with them.4. Once the cables were completed, I plugged them into a H!Fiber NIC (Intel I350-T4 chipset). They all fit nicely together, even with the boots. That network card is not the V2, and that was expected. The V2s are harder to find and there are no performance differences. The revision was made to fix a slight power surge during power-on. The network card performed flawlessly with pfSense and I was able to configure two LAGGs with LACP support. One to a Cisco managed switch, and the other to my cable modem (SB8200) but I’ll save those for a different review. This card is working perfectly.

First time making my own RJ45 cables for my POE camera system. Have done over 20 cables with this tool now without any issues!

These were very easy to work with. They have a large enough opening that I could even use them with my thick direct-burial Cat6a cable, although just barely. On the flip side, they were pretty loose on some of my older fairly thin Cat5 cables. They fit very nicely onto all of the various Ethernet connector ends that my cables used.

Easy to install and works great.

They're plastic boots, they do what they're supposed to do.

Je n'avais plus de capuchon et ils sont bien pratique pour protéger le connecteur RJ45. Fait le job.

gut

Ne ho utilizzati vanno bene

قليلة الجودة

Decent quality, fit on my CAT6 nicely and cover the heads well to protect them