REDTIGER F7N Dash Cam Hardwire Kit USB C Port, Dashboard Camera Car Charger Cable Kit 12V- 24V to 5V w/Fuse Kit, Low Voltage Protection for Dash Cam Double-4 Fuses

This Dashcam Hardware(HW) kit has a USB-C connector and worked with my Redtiger F7N Touch. One BIG plus is that the dashcam starts up much quicker. With the standard ACC adapter, the F7N takes an excruciating 21 seconds to start recording. I can be well on the road by then. With the HW kit, the dashcam switches from parking mode to recording in a second or two. It also displays the voltage of the battery and the cutoff voltage. I stuck it to my dash so I can see these voltages easily, but you can easily put it near your fuse box if you want it out of sight. The kit comes with a bunch of 'Fuse Taps' so you can find B+ and ACC power. I had to use a voltmeter to find the active side of the fuse after removing the fuse because the power side was not always on the 'top.' I cracked the case open and I did not see any red-flags with the the electronics - it looks well built. Below are the connections from the Regulator to the USB-C pins. This is important because the dashcam needs to get constant power for its time-lapse parking monitor mode and needs to know when the car is started (ACC goes active) to start live recording, and these signals need to be on the correct pins. Below are the connections from the HW kit wires to the USB-C conector. Red Tiger HW kit USB-C Pinout Black wire: USB-C pins B1,B12 A1,A12 (All GND pins) Yellow wire: Battery+ USB-C pins A4,A9 & B4,B9 (All VBUS pins) Red wire: Switched Acc USB-C pins A5,A8 & B5,B8 (cc1,sbu1,cc2,sbu2) The F7N seems satisfied with receiving the ACC signal on just the cc1/cc2 pins, and this seems to be a dashcam 'standard' if you can call it that. This was verified by using a generic HW kit that did not have connections to sbu1, sbu2. The battery protection cutoff voltage is adjustable with 3 cutoff voltage choices and a digital voltage display, which can be nice to monitor your battery condition. The only issue I have with this HW kit is that sometimes the display does not light up, making me think it is not working. When I start the car, my dashcam starts up but the display does not illuminate with ACC. If I move the voltage cutoff switch, then the display lights up, displays the new cutoff voltage, then it displays ACC. So a minor 'glitch' in the display, but overall it seems to work.

I bought this hardwire kit for my dashcam so I could keep my windshield clean and power the camera without needing to plug it into the cigarette lighter—and I’m super happy with it! Installation was easier than I expected. The instructions were clear, and all the necessary fuse adapters and tools were included. I had it wired up and running in under 30 minutes, and I’m by no means a car expert. Just make sure to double-check your car’s fuse layout and use a multimeter if you’re unsure! The build quality is solid. The cables are thick, durable, and long enough to tuck neatly along the headliner and down into the fuse box. It also has low-voltage protection, which gives me peace of mind that my car battery won’t be drained if I leave it in parking mode overnight. Since installing it, my dashcam starts up instantly with the ignition and switches into parking mode perfectly. Zero issues so far. If you're looking to clean up your setup and get the most out of your dashcam, this hardwire kit is definitely worth it. Clean look, reliable power, and one less thing to think about.

This did just the trick for concealing the power for my F7N Touch dash cam! A few things I will say that I don't remember reading in other reviews, and in case it helps others. One review said they noticed the accessory and constant power wires were mislabeled relative to the instructions, but that was not my experience. Unless I misread the instructions, I was confused why the appropriate fuse taps for my car came with a generic 10 amp fuse preinstalled and had an fuse empty slot below, surely a rookie mistake but I soon found that blank fuse slot on the taps are where I put my vehicle's original fuse that I pulled out, I guess the vehicle fuse I put in the empty slot is supposed to protect the actual equipment assigned to that fuse and the pre-installed fuse is to protect the camera. Lastly, I used my audio fuse as the accessory tap thinking surely that would be ideal because anytime the car is not on or in accessory mode my entire audio system is off. However, when my dash cam would never turn off after connecting it, I realized the audio fuse was actually hot constantly/ all of the time. I didn't have a micrometer to test the fuse, so I just assumed the audio would be a good accessory tap but that wasn't the case. So if you don't have a multimeter to check when a certain fuse is hot and when it's not, this is just something to keep in mind that's something you think could be a good accessory tap might not actually be. Again might be a rookie mistake on my part but maybe this helps somebody else in the future. In general I found the kit fairly easy to install, and I'm not using parking mode right now but it's nice to know I can, I might test it out in the future but I am worried about how quickly it will drain my car battery if the car is sitting for a couple of days (I have a portable jump starter so not a big deal of it dies but still... Not ready to test the waters with parking mode yet). In general, I would recommend this hardwire kit! Some of the hardwire external backup power source kits would also be a great option but those are much more expensive

Easy setup, good compatibility, and essential for a dash cam. Great product.

Super Qualität

Très pratique pour installer la dashcam REDTIGER avec branchement électrique permanent protégé par un fusible. Tout est prévu. Il y atout les différentes sortes de fusibles que l'on peut trouver dans nos voitures. Longueur de fil plus que suffisante. Je recommande

This kit works well - allows the camera to go into parking mode - comes with everything you need and is easy to use. The cable that goes to the front camera could be longer (so I could site the control box where I wanted it) but I managed quite well. Decent value for money - it makes my camera look professionally fitted.

خرب معي وتم التواصل من خدمة العملاء وحل المشكلة.